Top Ad Widget

Collapse

Announcement

Collapse
No announcement yet.

I'm a huge fan of Hogue pistol grips. I heard they make overmolded rifle stocks to replace old ones, which is exactly what I did

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • I'm a huge fan of Hogue pistol grips. I heard they make overmolded rifle stocks to replace old ones, which is exactly what I did

    I'm a huge fan of Hogue pistol grips. I heard they make overmolded rifle stocks to replace old ones, which is exactly what I did. I'm still awaiting for it to come in. Few questions. Do I need to loc-tite the barrel screw that joins the stock to the barrel? Is changing this stock gonna affect accuracy to the point that I need to completely re-zero my scope? These and any other information is greatly appreciated. Hope everyone is enjoying the summer. So far, too hot for me.

  • #2
    not like your accuracy can get much worse! might as well duck tape and super glue her on!

    Comment


    • #3
      I'm not an expert on this subject, so keep that in mind, but I felt I had to add something to the conversation to offset kkok's stupid drivel.
      I've never completely replaced a rifle stock, but I've taken them off and on to clean the guns before, and in my experience, you don't need to Loc-Tite the barrel screw, just screw it down nice and tight, and it should hold fine, unless you're shooting a very hard-kicking gun. But it wouldn't hurt to Loc-Tite the screw, if it'd make you feel better.
      I don't think the new stock will have a huge impact on accuracy, but it will probably shift it a bit - probably a few inches at 100 yards, so you will have to shoot it after putting the new stock on.
      We haven't had too much heat in my part of the country, but we've had WAY too much rain - we just got 3.6 inches last night and this morning, so all the creeks are flooded.

      Comment


      • #4
        I wouldn't use Loctite on the action screws. Just make sure they are tight when you install the action in the new stock. I would definitely check where your rifle is shooting after you get it put together, most likely it will affect your point of impact.

        Comment


        • #5
          I have installed two synthetic stocks one, a Remington model 700, another Weatherby Mark V.
          I also glass bedded the Weatherby and the POI was off slightly. BTW, the Weatherby has a inch-pound specification for tightening the action screws.
          The Remington was a drop in and also needed a slight tweak.

          Comment


          • #6
            Hogue makes two different rifle replacement stocks. One has an aluminum insert to stiffen the stock. That one is more costly but I believe it would be worth it. I have never tried Hogue's gun stocks but their reputation is top notch. Last thing, do not Loctite the action screws.

            Comment

            Welcome!

            Collapse

            Welcome to Outdoor Life's Answers section. Here you will find hunting, fishing, and survival tips from the editors of Outdoor Life, as well as recommendations from readers like yourself.

            If this is your first visit, be sure to check out the FAQ for information on posting and navigating the forums.

            And don't forget to check out the latest reviews on guns and outdoor gear on outdoorlife.com.

            Right Rail 1 Ad

            Collapse

            Top Active Users

            Collapse

            There are no top active users.

            Right Rail 2 Ad

            Collapse

            Latest Topics

            Collapse

            • Neighbor painted me a picture!
              by dewman
              My neighbor is a regionally known artist. So over time after regaling him with childhood hunting stories of my younger years in Michigan, South Dakota,...
              05-03-2021, 03:35 PM
            • What would you do?
              by fitch270
              About 15 minutes after daybreak my daughter nudges me in the side. I’ve been letting out some soft yelps and clucks but the turkeys are quiet early...
              05-01-2021, 09:34 PM
            • Holy flock 2
              by fitch270
              First a question, then why it matters.


              A group of bears is called what?


              Times up: The answer is

              ...
              05-01-2021, 08:49 PM
            • Opportunity knocking
              by fitch270
              I should probably hold off on mentioning this for a bit but here we go.

              Got the annual pre-season turkey call (lol) from my cousin last...
              04-27-2021, 08:29 PM
            • Iron sights, Yes, No, Maybe?
              by fitch270
              I’ve been thinking on this one since reading Amflyer’s response to me on his Not Available Rifle thread. The subject of the iron sights came up, I...
              04-26-2021, 10:41 PM

            Right Rail 3 Ad

            Collapse

            Footer Ad Widget

            Collapse
            Working...
            X